Services

In this article down the page you will discover lots of awesome insight with regards to How to Install a Bathtub Yourself.

Installing a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently available, the project can relocate quickly; if you need to open a wall surface to remove the old tub and also place the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Make sure you have actually qualified yourself for the task as well as are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need a professional plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently purchased a new bathtub and do not need to transform the setup of your previous water system pipelines.
Your tools as well as product checklist ought to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installment

To start with, the supporting frame provided with the bath must be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final setting.

Removing Old Touches

If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

Installing the Bathtub

Using both wood boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and new pipework for leakages and tighten them if needed. Fill up the tub as well as also check the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has actually been utilized a minimum of when as this will certainly settle it into its final position.

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind must be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in problems with dampness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof adhesive and grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Hopefully you enjoyed reading our section on How to Install a Bathtub. Thanks for taking a few minutes to browse our content. Are you aware of somebody who is fascinated by How to Install a Bathtub? Take a moment to share it. We appreciate reading our article about How to Install a Bathtub Yourself.

Avoid more damage, call now!